SEARCH RESULTS

< Back Stainless Steel Spacers Product Type: Cable Railing Accessory REQUEST A QUOTE Used to support thin-walled double end post design or allow for Receiver extension in a stair system. CABLE DIAMETER PART NO. LENGTH OUTSIDE DIAMETER WALL THICKNESS 1/8", 3/16" CH-SPC-R6-.500 .500" 5/8" .083" 1/8", 3/16" CH-SPC-R6 .970" 5/8" .083" 1/4" CH-SPC-R8 .970" 3/4" .095"

< Back Adjust-A-Body With Clevis Post Types: Wood Fitting Types: Swaging, Tensioning REQUEST A QUOTE Exposed, swaged, tensioning, face-of-the-post-mounted fitting suitable for level or pitched runs and is available for 1/8˝ and 3/16˝ diameter 1×19 stainless steel cable. Can be used with any fitting on the opposite end of the run. Consists of two separate pieces: the articulating Threaded Lag and Adjust-a-Body® tensioning body. Threaded Clevis is installed into a pre-drilled or tapped hole in the end post. Cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. Use of this fitting requires an appropriate sized ferrule that is swaged onto the cable, which much be purchased separately. Once sufficient tension is achieved, the Lock Nut is secured against the end of the body to secure the fitting from loosening. CABLE DIAMETER PART NO. USE WITH FERRULE NO. "T" THREAD "Lt" "Ln" "Lr" "D" DIAMETER 1/8" METAL: CH-A-J6-CL-M WOOD: CH-A-J6-CL-W COMP: CH-A-J6-CL-C CH-F-4 5/16-24 LH 2.00" .375" 2.73" .490" 3/16" METAL: CH-A-J6-CL-M WOOD: CH-A-J6-CL-W COMP: CH-A-J6-CL-C CH-F-4 5/16-24 LH 2.00" .375" 2.73" .490"

< Back Adjust-A-Body With Concrete Anchor Bolt Post Types: Concrete Fitting Types: Swaging, Tensioning REQUEST A QUOTE The Adjust-A-Body® with Concrete Anchor Bolt is an exposed, swaged, tensioning, face-of-the-surface-mounted fitting that is recommended for level runs terminating at a concrete surface only. This fitting is available for 1/8”, 3/16”, and 1/4” diameter 1×19 stainless steel cable. The Adjust-A-Body® with Concrete Anchor Bolt can be used with any fitting on the opposite end of the run. A concrete anchor is driven into a pre-drilled hole in the concrete surface. The short thread of the anchor bolt portion of the fitting is threaded into the concrete anchor. The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed all the way onto the exposed machine thread of the anchor bolt, followed by the body, which is secured onto the anchor bolt until effectively creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to prevent the fitting from loosening. Use of this fitting requires that an appropriately sized ferrule is swaged onto the cable. Ferrule sold separately, see information on page 8. The Red Head® Concrete Anchor is available for purchase at many building supply retailers and distributors throughout the country. CABLE DIAMETER PART NO. USE WITH FERRULE NO. "S" "T" THREAD "Ls" "LT" "LOQ" "LN" "LR" "D" USE WITH "RED HEAD" BRAND USE WITH "RED HEAD" BRAND 1/8" CH-A-JAB6 CH-F-4 3/8-16 5/16-24 LH .500" 2.313" 3.188" .375" 2.75" .490" RM-38 SRM-38 3/16" CH-A-JAB6 CH-F-6 3/8-16 5/16-24 LH .500" 2.313" 3.188" .375" 2.75" .490" RM-38 SRM-38 1/4" CH-A-JAB8 CH-F-8 1/2-13 7/16-20 LH 1.125" 2.500" 3.938" .500" 3.00" .617" RM-12 SRM-12

< Back Adjust-A-Body Threaded Eye and Threaded Tab or Lag Eye Post Types: Metal Fitting Types: Swaging, Tensioning REQUEST A QUOTE The Adjust-A-Body® with Threaded Eye fitting is an exposed, swaged, tensioning, face-of-the-post-mounted fitting that can be used on level or pitched runs. This fitting is available for 1/8”, 3/16”, and 1/4” diameter 1×19 stainless steel cable. The Adjust-A-Body® with Threaded Eye can be used with any fitting on the opposite end of the run. This fitting attaches to the end post by installing a Threaded Tab into a pre-drilled and tapped hole in the end post and attaching the threaded eye portion of the fitting to the threaded tab with a button head screw. The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed all the way onto the threaded eye first, followed by the body, which is secured onto the eye, creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to secure the fitting from loosening. While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the threaded eye portion of the fitting pivots at the tab. Use of this fitting requires that an appropriately sized ferrule is swaged onto the cable. Ferrule sold separately. CABLE DIAMETER PART NO. USE WITH FERRULE USE WITH SCREW NO. USE WITH LAG EYE USE WITH TAB NO. "E" THREAD "A" "B" "S" "T" THREAD "Lt" "Ln" "Lr" "D" DIAMETER 1/8" CH-A-JTE6 CH-F-4 CH-SC-6 CH-LE-6 CH-TT-6B 1/4-28 .233"/.299" .500" .44" 5/16-24 LH 2.00" .375" 2.75" .490" 3/16" CH-A-JTE6 CH-F-6 CH-SC-6 CH-LE-6 CH-TT-6B 1/4-28 .233"/.229" .500" .44" 5/16-24 LH 2.00" .375" 2.75" .490" 1/4" CH-A-JTE8 CH-F-8 CH-SC-8 CH-LE-8 CH-TT-8B 3/8-24 .295"/.285" .874" .68" 7/16-20 LH 2.50" .500" 3.00" .617"

< Back 672 Series APPLICATION GUIDE Cable Kit Length: 30' - 60' REQUEST A QUOTE Post Type: Wood Inside-of-post to outside-of-post mount - Use minimum 4x4 wood end posts LEFT PART NO. RIGHT PART NO. CH-A-JB6 CH-R-6-12 CH-PLST-4 / CH-PLST-6 FS-7/16-FLATW-18-8

< Back Radius Ferrule - Stop Gauge Product Type: Cable Railing Accessory REQUEST A QUOTE Use this gauge to confirm that the radius ferrules, studs and clip-on stops have been properly swaged. PART NO. CT-RF-GAUGE

< Back Grommet Installation Kit Product Type: Installation Equipment REQUEST A QUOTE Needed to properly install grommets. Place the grommet on the tool, align the grommet over the hole, and tap lightly with a hammer. PART NO. CT-GROMMET-TOOL-SET

< Back 212 Series APPLICATION GUIDE Cable Kit Length: 5' - 25' REQUEST A QUOTE Post Type: Metal Outside-of-post to outside-of-post mount for 1 1/2" posts LEFT PART NO. RIGHT PART NO. CH-R-6-12 CH-PUL-4-12 / CH-PUL-6-12 CH-W-R6B CH-W-R6B

< Back Cut off Tool Kit Product Type: Installation Equipment REQUEST A QUOTE Used to cut cable flush with the end of Pull-Lock® fittings, and to cut excess threads off stud-type tensioners. Includes mandrel and two cut-off wheels. PART NO. CT-CUT-OFFKIT

< Back Stainless Steel Beveled Washer Product Type: Cable Railing Accessory REQUEST A QUOTE For use with Invisiware ® Receivers, Radius Ferrules, Push-Lock tensioners and Pull-Lock fittings on stairways or slopes where you need to drill your end post holes at an angle. CABLE DIAMETER STAIR/SLOPE PITCH PART NO. 1/8", 3/16" 30° - 33° CH-BW32-6 1/8", 3/16" 34° - 36° CH-BW35-6 1/4" 37° - 39° CH-BW38-8 1/4" 30° - 33° CH-BW32-8 5/16" , 3/8" 34° - 36° CH-BW35-12 5/16" , 3/8" 37° - 39° CH-BW38-12 5/16" , 3/8" 30° - 33° CH-BW32-12

< Back Stainless Steel Cleaner and Protectant Product Type: Cable Railing Accessory REQUEST A QUOTE E-Z Clean Dissolves minor corrosion, then leaves a protective coating that lasts for months. Includes an 8-oz. spray-on rust and stain remover and a 4-oz. bottle of protectant. PART NO. CH-EZ-CLEAN

< Back Invisiware Receiver Post Types: Wood, Metal Fitting Types: Swaging, Tensioning REQUEST A QUOTE The Invisiware® Receiver with Invisiware® Stud combination is a concealed, swaged, tensioning, through-the-post-mounted fitting. Can be used for level or pitched run Compatible for wood post application Use with 1/8” or 3/16” diameter 1×19 stainless steel cable The Invisiware® Receiver with stud can be used with any fitting on the opposite end of the run. The receiver is placed and concealed within a pre-drilled hole in the wood end post (a minimum of 3” of clearance between the back side of the post and a structure is required to allow installation of the Receiver). We recommend placing a stainless steel flat washer between the fitting shoulder and the mating surface of the wood post. The stud is swaged onto one end of the cable and is inserted and screwed into the Receiver installed in the end post. Tension is created by rotating the Receiver (with a hex wrench inserted into its broached end) and drawing the stud into the Receiver. This fitting can also be used in pitched applications using the same horizontally drilled method for 4×4 wood posts. The same method works for larger posts by installing a post protector tube on the cable exit-to-pitch side of your wood end post. This fitting is commonly paired with a Pull-Lock® on the opposite end of the run. RECEIVER DIMENSIONS CABLE DIAMETER 1/8" CABLE 3/16" CABLE 1/4" CABLE 5/16" CABLE 3/8" CABLE Part Number CH-R-6-XX CH-R-6-XX CH-R-8-XX CH-R-12-XX CH-R-12-XX "D" Diameter .437" .437" .531" .687" .687" "T" Thread 5/16-24 5/16-24 7/16-20 9/16-18 9/16-18 "H" Hex 3/16" 3/16" 7/32" 5/16" 5/16" "S" Diameter .537" .537" .646" .865" .865" "L" Length See "FRAMING OPTIONS" Table See "FRAMING OPTIONS" Table See "FRAMING OPTIONS" Table See "FRAMING OPTIONS" Table See "FRAMING OPTIONS" Table FRAMING OPTIONS FOR RECEIVER CABLE DIAMETER 1/8" CABLE 3/16" CABLE 1/4" CABLE 5/16" CABLE 3/8" CABLE FRAME OPTIONS PART NO. PART NO. PART NO. PART NO. PART NO. "L" LENGTH 1-1/2" Tube* or 1-1/4" Pipe CH-R-6-12 CH-R-6-12 NA NA NA 1.56" 1-1/2" Pipe CH-R-6-22 CH-R-6-22 CH-R-8-22 NA NA 1.81" 2" x 2" Tube* CH-R-6-32 CH-R-6-32 CH-R-8-32 CH-R-12-32 CH-R-12-32 2.03" 2" Pipe CH-R-6-42 CH-R-6-42 CH-R-8-42 CH-R-12-42 CH-R-12-42 2.30" 2-3/8" Tube* CH-R-6-72 CH-R-6-72 NA NA NA 2.405" 2-1/2" Tube* CH-R-6-82 CH-R-6-82 NA NA NA 2.53" 3" Tube* CH-R-6-52 CH-R-6-52 CH-R-8-52 CH-R-12-52 CH-R-12-52 3.03" 3-1/2" Tube* CH-R-6-62 CH-R-6-62 NA NA NA 3.5625" 4x4 Min. Wood Post CH-R-6-62 CH-R-6-62 NA NA NA 3.5625" *Round or Square Tube