SEARCH RESULTS

< Back Stainless Steel Post Protector Tube Product Type: Cable Railing Accessory REQUEST A QUOTE The corner tube is inserted into a wood post where the cable enters/exits the post at an angle to keep the cable from biting into the wood. PART NO. CH-CS-TUBE-6

< Back 702 Series APPLICATION GUIDE Cable Kit Length: 5' - 25' REQUEST A QUOTE Post Type: Metal Inside-of-post to outside-of-post mount for 1 1/2" posts LEFT PART NO. RIGHT PART NO. CH-R-6-12 CH-PL-TH4 / CH-PL-TH6 CH-W-R6B

< Back 601 Series APPLICATION GUIDE Cable Kit Length: 5' - 50' REQUEST A QUOTE Post Type: Wood Inside-of-post to outside-of-post mount - Use minimum 4x4 wood end posts LEFT PART NO. RIGHT PART NO. CH-R-6-62 CH-PL-L4 / CH-PL-L5 FS-7/16-FLATW-18-8

< Back Invisiware Radius Ferrule Post Types: Wood Fitting Types: Swaging REQUEST A QUOTE The Invisiware® Radius Ferrule is a concealed, swaged, non-tensioning, through-the-post-mounted fitting that is suitable for pitched or level runs. This fitting is available for 1/8” and 3/16” diameter 1×19 stainless steel cable. The Invisiware® Radius Ferrule must be used with a tensioning fitting on the opposite end of the run. It is the least expensive through-the-post fitting that we offer. This fitting has a head shaped to appear like the Invisiware® Receiver from the outside of the post (like the Receiver, the Radius Ferrule is concealed within the post). For these two reasons it is recommended to use the Invisiware® Radius Ferrule on one end of your cable run and an Invisiware® Receiver with stud on the opposite end whenever practical to do so. The only reason not to consider this fitting as your non-tensioning end would be if you preferred to use a swageless solution. This fitting installs into a hole drilled through the face of the post (to accommodate the cable at minimum) and a hole through the back side of the post to accommodate the fitting. It also requires that you have at least 2” of clearance on the back side of your end post so you have enough workspace to feed the rest of the cable through the post prior to pulling the Radius Ferrule into its final position. (The cable would likely be attached to the Radius Ferrule prior to installing it through the back side of the post). We recommend using a stainless steel flat washer between the shoulder of the fitting and the mating surface of the wood post. You can use this fitting on a pitched application by installinga post protector tube into the face of the post where the cable exits at an angle. The post protector tube protects the face of the post from abrasion and furrowing as the cable is tensioned. The post protector tube is sold separately. CABLE DIAMETER PART NO. "D" DIAMETER AFTER SWAGED "L" LENGTH AFTER SWAGED "S" HEAD DIAMETER "A" SHOULDER DIAMETER 1/8" CH-RF-4 .250" .750" .537" .437" 3/16' CH-RF-6 .250" .750" .537" .437" 1/4" CH-RF-8 .375" 1.000" .646" .531" 5/16" CH-RF-10 .500" 1.000" .865" .687" 3/8" CH-RF-12 .500" 1.000" .865" .687"

< Back Cable Cutter Product Type: Installation Equipment REQUEST A QUOTE For burr-free cutting of cable. CABLE DIAMETER PART NO. 1/8", 3/16", 1/4" CT-CC-3

< Back Ferrule Product Type: Cable Railing Accessory REQUEST A QUOTE The ferrule is used to retain an Adjust-A-Jaw, Adjust-A-Body, or a Fixed Jaw onto the cable. AFTER SWAGED AFTER SWAGED CABLE DIAMETER PART NO. "D" DIAMETER "L" LENGTH 1/8" CH-F-4 .250" .61" 3/16' CH-F-6 .250" .56" 1/4" CH-F-8 .375" .70" 5/16" CH-F-10 .500" .73" 3/8" CH-F-12 .500" .71"

< Back Push-Lock Post Types: Wood, Metal Fitting Types: Swageless REQUEST A QUOTE The Push-Lock® is a concealed, swageless, non-tensioning, through-the-post-mounted fitting that is suitable for use on level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable. The Push-Lock® must be used with a tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled hole in the end post. Using the Push-Lock® fitting on level runs requires that a minimum of 1-1/2” of clearance exists on the back side of the end post (to install the fitting through the back side of the post). It is also recommended that a stainless steel flat washer be installed between the shoulder of the fitting and the mating surface of the wood post. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools. This fitting is made to look similar to the Invisiware® Receiver from the exterior of the post, so it is recommended to use a Receiver with stud on the opposite end whenever practical to maintain a consistent look. 1/8" CABLE PART NO. 3/16" CABLE PART NO. FRAME "F" FRAME "R" FRAME "P" "L" LENGTH CH-PL-4-12 CH-PL-6-12 1-1/2" 1-1/2" 1-1/4" 1.562" CH-PL-6-2.030 CH-PL-6-2.030 2" 2" 1-1/2" 2.030" CH-PL-4-3.030 CH-PL-6-3.030 3" 3" NA 3.030" CH-PL-4 CH-PL-6 4" x 4" NA NA 1.562"

< Back Electric Hydraulic 120V Pump Product Type: Installation Equipment REQUEST A QUOTE Increase swaging speed with this electric hydraulic pump versus the Air Over Hydraulic Pump. No compressor is needed on the job site and it saves you time. All you need is electric on the site to plug in the pump. PART NO. CT-HYD-PUMP-ELEC

< Back Clip-on Fixed Jaw and Threaded Tab or Lag Eye Post Types: Metal, Wood Fitting Types: Swaging REQUEST A QUOTE The Clip-On Fixed Jaw is externally a duplicate of the Fixed Jaw and is only available for 1/8” and 3/16” diameter 1×19 stainless steel cable. The Clip-On Fixed Jaw was created for applications that called for factory swaged fittings on both ends of the cable, without requiring over-sized holes through the intermediate posts (so an entire Fixed Jaw could pass through). This fitting accomplishes that with a .250” diameter ferrule that is pre-swaged to the cable. Once the cable with just a ferrule swaged to it is run through the intermediate posts to the end post to which it will attach, the jaw is slipped onto the cable over the ferrule and the clip installed at the ferrule. The jaw then slides back against the clip, which prevents the fitting from coming off the cable. This fitting attaches to the wood end post by installing a Lag Eye into a pre-drilled hole in the end post and attaching the Clip-On Fixed Jaw to the lag eye with a button head screw. Lag eye and screw sold separately. Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must also be purchased separately. WOOD METAL CABLE DIAMETER PART NO. USE WITH FERRULE USE WITH SCREW NO. USE WITH LAG EYE USE WITH TAB NO. "F" DIAMETER "G" "K" "L" 1/8" CH-F-JC2-4 CH-F-4 CH-SC-6 CH-LE-6 CH-TT-6B .260" .260" .56" 1.75" 3/16" CH-F-JC2-6 CH-F-6 CH-SC-6 CH-LE-6 CH-TT-6B .260" .260" .56" 1.75"

< Back Push-Lock Tensioner With Hanger Bolt Post Types: Wood Fitting Types: Swageless, Tensioning REQUEST A QUOTE The Push-Lock® Tensioner with Hanger Bolt is an exposed, swageless, tensioning, face-of-the-post-mounted fitting that is suitable for level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable. It is a more compact design than our swaged Adjust-A-Body® fittings. The Push-Lock® Tensioner with Hanger Bolt can be used with any fitting on the opposite end of the run. This fitting consists of two separate pieces: the hanger bolt and Push-Lock® tensioning body. The hanger bolt is driven into a pre-drilled hole in face of the wood end post. The cable attaches to the body via our Push-Lock® locking wedge system which requires no special tools. The machine thread of the hanger bolt threads into the body, connecting the two pieces. Tension is created by securing the post-side segment of the body onto the machine threads while preventing the cable-side segment of the body from turning. The Push-Lock® Tensioner with Hanger Bolt can be used with sleeved posts as well. We do not recommend this fitting being installed in pitched applications because it would require drilling all of the holes in the end post at an angle. While this is possible with special fixtures, if it is not done correctly the end result would be visually unacceptable. CABLE DIAMETER PART NO. 1/8" CH-PL-SFC-WS-4 3/16" CH-PL-SFC-WS-6

ABOUT US OUR WORK AS&D designs, manufactures, and distributes aluminum systems for dealers, distributors, and wholesalers in the construction industry. We prioritize building long-term relationships and use recycled aluminum to provide eco-friendly, durable, and lightweight products. STUNNING RESULTS, APPLICATIONS TO INSPIRE 1/5 The AS&D product line offers you modern designs with inspiring application ideas for your next railing , balcony , sunshade , or patio cover project. SERVING OUR CUSTOMERS We offer design, estimating, and national fulfillment through our manufacturing facilities and warehouses. As a family-owned manufacturer, we prioritize you and your company to reduce installation challenges. We provide accurate project designs and materials with easy on-site installation. We're happy to assist you each step of the way. OUR CULTURE 1/1 AS&D values its employees and strives for excellence in all areas of the company. We prioritize customer satisfaction and mentor the next generation of workers through partnerships with local organizations and trade schools. GIVING BACK TO THE COMMUNITY At American Structures and Design, we believe that a company’s true success is not only measured by the quality of its products and services but also by its impact on the community it serves. We are committed to making a positive difference through active involvement in community initiatives, charitable contributions, and volunteer efforts. OUR LOCATIONS 1801 132nd Ave. E, STE 100, Sumner, WA 98390 | P: 877-887-9828 F: 253-833-4545 | M-F: 8:00-4:30 PT 13444 NE Jarrett St., Portland, OR 97230 | P: 877-887-9828 F: 971-645-4212 | M-F: 8:00-4:30 PT

CONTACT US If you have any questions or need more information about our products, don't hesitate to contact us. You can reach us by filling out the provided form or by calling us directly at 877-887-9828 . We strive to reply to all inquiries within 24 hours. ​ ​ Looking to apply for a job? Go to our careers page ​ Have any suggestions for AS&D? Submit anonymous feedback ​ First Name Email Company: City: Zip: Last Name Phone Address: State: How did you hear about us? Subject Message Upload File Upload supported file (Max 15MB) I agree to receive monthly newsletters from American Structures and Design. AS&D will only send you information if you agree to receive it and you may opt-out at anytime. AS&D will not share or exchange your information. Send Message Thank you for contacting us. Someone will respond within 24 hours.